iPhone 16e Teardown: Test Mule or Worth It? (Weekihome)
We tear down the iPhone 16e: 14-sized screen, cut-down A18, Apple's own C1 modem, 4005mAh battery and IP68. Test mule or worth buying?
In the 2025 Chinese smartphone market, Apple is the only manufacturer offering a phone priced above 4,000 yuan with a single main camera. The iPhone 16e's exterior is one of its few strengths. Its screen matches the iPhone 14 in size, and a tempered glass film made for the iPhone 14 fits it without modification. This teardown examines whether the internal components are also shared with other models.
Disassembly Procedure
Step 1: SIM Tray
- Power off the device and remove the SIM tray.
- The two SIM slots are placed back to back.
- The tray is machined from a single block of aluminum alloy using CNC processing.
- A dust- and water-resistant rubber ring is fitted on the inner side.
Step 2: Rear Cover
- Remove the two bottom screws.
- Heat the device, insert a blade at the bottom of the rear cover, and pry open a gap.
- Use a plastic opening tool to cut the adhesive around the perimeter.
- Open the cover from left to right.
- The wireless charging flex cable on the right remains connected to the logic board. It must not be pulled or damaged.
- Remove one screw, lift the cover plate, pry open the connector, and separate the rear cover.
Rear cover findings:
- The rear cover is glass.
- Apple dropped the color-fusion process and offers only black and white.
- The 3D cold-sculpted camera bump, used on previous models for years, has been removed to reduce cost.
- The camera lens protector remains sapphire glass.
Interior layout:
- Dust-proof sealing foam surrounds the rear camera.
- Heat-dissipation film covers the wireless charging coil and the positions corresponding to the ROM and the haptic motor.
- Black stickers in other areas provide mainly insulation and protection.
- A metal reinforcement plate beneath the heat-dissipation film covers nearly all areas except the secondary board. It increases the cover's impact resistance and expands the heat-dissipation area.
- Metal clips on the edges secure the cover to the midframe with adhesive.
MagSafe:
- Lifting the heat-dissipation film over the wireless charging coil shows that the MagSafe ring magnets have been removed.
- Users who want magnetic charging must buy a case with magnets or attach a magnetic ring separately.
Two screws beside the rear camera are then removed, and the cover plate is lifted. The wireless charging flex cable also integrates the rear microphone and flash.
Step 3: Main Body and Battery Disconnection
- The 16e's layout differs from the 16. It is closer to a revised iPhone 14.
- The dual-camera system has been removed.
- The logic board has been redesigned, and the freed space is allocated to the battery to improve battery life.
- Remove two screws and the cover plate.
- Disconnect the battery connector first to cut power.
Step 4: Display
- The display is removed using the same method as the rear cover: heat the device, pry open a gap with a blade, cut the adhesive with a plastic tool, and open the display from right to left.
- The sensor flex cable and the display flex cable on the left remain connected to the logic board.
- Remove two screws and two cover plates, then disconnect two connectors to separate the display.
Display supplier:
- According to the foreign media outlet TechInsights, BOE is the main display supplier for the 16e.
- Samsung and LG supply secondary components.
Display specifications:
- Despite the "16e" name, the display specifications are closer to the iPhone 14 than to the 16.
- The display has no Dynamic Island and does not use the new Ceramic Shield glass.
- At the same size, the resolution differs from the 16.
Compatibility test:
- The team installed an iPhone 14 display assembly on the 16e body. Both display and touch functions worked normally.
- The iPhone 14 display assembly does not fit perfectly. The bottom edge leaves a gap because the position of the bottom clips has changed.
Display structure:
- The back of the display uses the metal backplate typical of iPhone models.
- The edge uses a hidden plastic bracket formed by low-pressure injection molding, known as LIPO packaging.
- Metal clips on the inner side of the bracket insert into the midframe to secure the display.
- Dust-proof sealing foam surrounds the infrared camera and the dot projector.
- The display driver board is protected by a metal cover that also helps dissipate heat.
- All ICs on the driver board are custom designed by Apple. Their specific models are not known.
Remove two screws below the Face ID area and lift the metal cover. Beneath it are the front ambient light sensor, the proximity sensor, and the top microphone.
Brightness:
- Measured maximum manual brightness is 790 nits.
- Brightness does not increase further under strong light.
Midframe:
- The midframe near the display shows only minor differences from the iPhone 14. The 16e is essentially a fine-tuned version of the 14.
Step 5: Main Assembly and Face ID Module
- Remove the screws that secure the flex cable connectors, then lift the cover plate.
- Disconnect all connectors on the logic board.
- Remove the Face ID module.
Compared with the iPhone 14, the Face ID module has slight changes to the flex cable style. The component configuration and layout order remain the same.
- The front camera is the Sony IMX 714, which Apple used from the iPhone 14 through the 16 Pro Max.
- A buffer foam and heat-dissipation film cover the back of the module. They protect the lens assembly and improve heat dissipation.
Remove all screws that hold the top speaker and lift it out.
- The speaker has adhesive attached to the antenna module.
- The speaker box differs greatly from the 16 but is largely the same as the 14.
- Both speaker enclosures are filled with acoustic enhancement material.
- The speaker unit size is most likely the same as the 14's.
Step 6: Rear Camera
- Remove all screws that hold the rear camera and then remove the plastic filler on the right side of the camera.
- Inspection of the filler revealed no functional structures.
- Remove the rear camera.
Rear camera sensor:
- The CMOS sensor is the Sony IMX 982, which is smaller than the 16's main camera sensor.
- It appears to be a revised version of the IMX 972, the ultra-wide sensor in the 16 Pro series.
- It does not use the second-generation sensor-shift stabilization of the 16 Pro, nor the first-generation sensor-shift stabilization of the 16.
- It uses a more conventional lens-shift stabilization solution.
Lens structure:
- The lens has a metal anti-roll frame.
- Machining marks on the back indicate that the frame is produced by CNC processing.
- A buffer foam on the midframe protects the lens assembly at the corresponding position.
Step 7: Logic Board
- Remove all screws that secure the logic board, then lift it out.
Structure:
- The logic board uses a double-layer stacked design.
- The lower board is 0.45 mm thick.
- All connectors on the board are protected by buffer foam.
- Both sides of the shield cans have heat-dissipation film.
- Small components along the bottom are sealed with glue.
Memory and processor:
- Peel off the heat-dissipation film to reveal the ROM, which is a Toshiba (Kioxia) NVMe-protocol storage chip.
- After heat-gun separation of the layers and removal of the thermal interface material, the RAM is visible above the processor.
- The RAM is 8 GB of Samsung LPDDR5X.
- Below the RAM is the A18, which is a severely cut-down version. It has already been reduced from the standard configuration, and Apple reduced its GPU to four cores.
Blow away all shield cans to reveal the chip layout.
- The core area uses the thermal insulation design typical of iPhone models.
- The A18 is sandwiched between two layers of the logic board. It faces the in-house C1 baseband modem directly.
- On the back of the A18 is Apple's power management IC, which adds to the heat load.
- Several pieces of foam are placed between the ROM, the Wi-Fi/Bluetooth module, and the layer above to block heat.
C1 baseband modem:
- Internal code name: APL1114.
- Manufactured on TSMC's N4 process.
Wi-Fi/Bluetooth module:
- The printed markings provide no useful information.
- It is likely a Broadcom solution.
- Compared with the 16, it is downgraded and supports only Wi-Fi 6.
RF components:
- No Qualcomm RF chip was found around the baseband.
- The components come from three major American RF suppliers: Qorvo, Skyworks, and Broadcom.
- The RF transceiver and RF power management on the back of the baseband are Apple's own. The RF transceiver is codenamed APL1088 and uses TSMC's 7 nm process.
- The Qualcomm SDR875 used in previous phones is manufactured on a 14 nm process. Apple's more advanced process is expected to lower power consumption.
- The RF power chip is APL1064.
Signal performance:
- Signal test results are widely available. The 16e performs competitively with the Qualcomm version, but only when compared with its own previous generation.
Power management:
- The main power supply on the back of the SoC is APL109A, the same chip used across the 16 series.
- No UWB chip was found on the board.
Midframe:
- The midframe at the logic board position has no thermal filler in the gaps, which is consistent with Apple's standard approach.
- A small piece of heat-dissipation film is applied only at the charging IC to remove heat.
Step 8: Bottom Components
- Remove one screw and take out the X-axis linear motor.
- The motor uses the same specification as the iPhone 14.
- It is smaller than motors across the 16 series.
- It still outperforms the CSA0916, which the team describes as the largest motor in the Android market.
Remove all screws that secure the SIM tray, then remove the tray.
- The SIM tray uses an independent modular design for easier repair.
Remove the screws at the secondary board area and take out the bottom speaker.
- The speaker box is smaller than the 16's.
- Compared with the 14, the differences are minor.
- The enclosure is also filled with acoustic enhancement material.
- The unit size is most likely the same as the 14's.
Remove the screws that hold the bottom microphone module and take the module out.
- Remove the metal cover on top.
- The three small holes on the module, from left to right, are the air vent for the barometric pressure sensor, the sound intake for the bottom microphone, and the pressure relief hole that balances internal and external air pressure.
- Inside, the barometric pressure sensor, the bottom microphone, and a white waterproof breathable membrane are visible.
- All cover plates on the device are metal.
- Buffer foam and metal conductive foam are present on the inner side of the cover plates.
Remove all screws that secure the tail connector flex cable, heat it, and remove the flex cable.
- Small components on the flex cable are sealed for protection.
- The flex cable integrates a second bottom microphone and a USB 2.0 Type-C port.
- The plastic housing of the Type-C port is off-white, matching the frame.
- The contact tongue is not fully populated, so the port does not support DisplayPort video output. The team notes that this is the only iPhone with a Type-C port that lacks DisplayPort video output.
- All pins are plated with an inert metal for better oxidation and corrosion resistance.
Microphones:
- The device has four microphones in total. It supports wind noise reduction and audio mixing.
- This configuration matches the 16 exactly.
Bottom frame:
- Foam rings are added to the inner side of the bottom frame at the microphone module and the Type-C port.
- The bottom speaker's sound outlet has an orange waterproof ring.
- The second bottom microphone's sound intake has a white waterproof breathable membrane.
- Metal dust meshes protect the internal openings.
Water resistance:
- The device has the same IP68 rating as the full 16 series.
- It can be submerged up to 6 meters for 30 minutes.
Step 9: Battery Removal
The 16e uses a new battery adhesive based on the same principle as the 16 series. A small metal tab sits at the bottom of the battery. Applying power allows the battery to be removed quickly.
The team's method:
- Set a DC adjustable power supply to 30 V.
- Attach a screw to the midframe to connect the negative terminal.
- Lift the tab.
- Connect the positive terminal to the tab and the negative terminal to the midframe.
- Wait 30 seconds, then remove the battery.
The adhesive stays intact on the back of the battery. Only slight tackiness remains. The power draw is very low, and the adhesive showed no temperature change during the process. The adhesive therefore does not lose its bond through heating.
Battery specifications:
- Single-cell, single-connector design.
- Rated capacity: 4,005 mAh.
- This is 726 mAh larger than the iPhone 14 and 444 mAh larger than the 16.
- Manufacturer: Dongguan Xinnengde (东莞新能德).
- Energy density, calculated from the package dimensions, is approximately 735 Wh/L. This is slightly higher than the 16's 733 Wh/L.
- Full specifications are available in the accompanying images.
Midframe:
- The midframe uses nano-injection molding combined with CNC machining, a method common in flagship phones.
- The outer frame and inner frame are both aluminum alloy.
- The anodized layer was cut away at the battery adhesive position so that the circuit can form when power is applied.
- The camera control button, the most recognizable feature of the 16 series, has been removed from the frame.
Assessment
The teardown indicates that the iPhone 16e is a cost-reduced device. Most core specifications have been reduced. Some peripheral components remain comparable to the 16 series. The A18 with fewer GPU cores and the in-house baseband modem allow the device to be placed within the 16 series.
The team views the 16e as more of a trial product for Apple. Signal performance is a complex engineering challenge, and Qualcomm's long-term accumulation of baseband experience is significant. The team does not conclude that Apple cannot develop a competitive modem. Competition benefits the market, but further iterations will be necessary.
For purchasing decisions, the team states that the 16e is difficult to justify on value for money. Users who want the basic iPhone 16 series and value the Apple ecosystem may still consider it.
Opening the Back Cover and Removing the SIM Tray
The SIM tray and back cover are removed. The 16e's glass back drops MagSafe magnets and the 3D camera-ring design, and uses a metal reinforcement plate.
- SIM tray is machined from a single block of aluminum alloy with CNC, with dust and water seals.
- Back cover is glass; the color-blending process was dropped, leaving only black and white.
- Sapphire glass is kept over the camera lens; the 3D cold-carved camera bump used on earlier Deco designs was removed.
- MagSafe ring magnets are absent around the wireless charging coil, so magnetic charging requires a magnetic case or added magnets.
- Metal reinforcement plate under the heat-dissipation film covers nearly all areas except the daughter board, improving impact resistance.
Display Removal and Comparison
The display is removed. It is the same size and structure as the iPhone 14 display, with a different panel supplier and no Dynamic Island.
- TechInsights reports BOE (京东方) is the main display supplier, with Samsung and LG as secondary suppliers.
- The 16e has no Dynamic Island and no new Ceramic Shield glass.
- Even at the same size, the display resolution differs from the 16; the specs match the iPhone 14.
- The iPhone 14 display assembly works fully on the 16e body, but its bottom edge leaves a gap because the bottom clip positions changed.
- Peak manual brightness measured at 790 nits; brightness does not increase further in strong sunlight.
Main Body, Logic Board, Camera, and Battery
The main body is removed. The front camera module and speakers are close to the iPhone 14, and the rear camera is a smaller IMX 982 with lens-shift stabilization.
- Front camera is the Sony IMX 714, the same sensor used from iPhone 14 through 16 Pro Max.
- Rear camera sensor is the IMX 982, smaller than the 16 main camera and a variant of the 16 Pro ultra-wide IMX 972.
- Rear camera uses traditional lens-shift stabilization, not the second-generation sensor-shift stabilization of the 16 Pro or the first-generation of the 16.
- Lens has a metal anti-roll cage made with CNC.
- Logic board is a double-layer stack with a 0.45mm lower board; a Kioxia (铠侠) NVMe ROM and a Samsung 8GB LPDDR5X RAM are used.
- A18 chip is further cut down to a 4-core GPU; it is sandwiched between two boards with the in-house C1 modem.
- C1 modem (internal code APL1114) is built on TSMC N4; the RF transceiver (APL1088) is TSMC 7nm, and the RF power chip is APL1064.
- The RF chips are from Qorvo, Skyworks and Broadcom rather than Qualcomm; the Wi-Fi module supports only Wi-Fi 6.
- No UWB chip was found on the board. Main power management chip is APL109A, the same as the 16 series.
- X-axis linear motor is the same spec as the 14 and smaller than the 16 series.
- Bottom speaker is smaller than the 16's, with similar acoustic materials; a second bottom microphone and USB-C port (USB 2.0) are present.
- The USB-C port's tongue is not fully pinned, so it does not support DisplayPort video output, making it the only USB-C iPhone without that feature.
- The device has four microphones with wind noise reduction and mixing, the same as the 16.
- Rated IP68, up to 6 meters for 30 minutes.
- Battery is removed by heating the adhesive with a DC power supply at 30V, applying current through a metal tab; the battery is 4005mAh, 726mAh more than the 14 and 444mAh more than the 16, from Dongguan Xinnengde (东莞新能德), with about 735Wh/L energy density.
- Midframe is nano-injection plus CNC one-piece with aluminum alloy, and the 16 Camera Control button is removed.
