iPhone Air Teardown: Apple's Extreme Stacking and a Preview of the Foldable
Apple's iPhone Air teardown reveals the extreme stacking behind its ultra-thin body: steel-cased battery, stacked motherboard, Deco expansion platform and a preview of
The iPhone Air uses a stacked internal architecture, with the Expansion Platform (the "Deco" area) integrating the main camera module, a T-shaped motherboard, and the A19 Pro processor. This teardown examines the back cover, display, motherboard, battery, ports, and mid-frame, and assesses how Apple reduced the device's thickness.
Overview
Previous ultra-thin designs focused mainly on miniaturizing components. The iPhone Air shows a different approach. The Expansion Platform, which Apple's marketing describes as a raised area around the camera, is used to house internal parts. Apple's English term for the platform is "Plateau," which refers to a highland.
The device uses a repair-friendly sandwich structure. The screen and back cover can be removed separately.
Back Cover
- Glass: The back cover uses Ceramic Shield glass, which is typically used only on displays. It has improved crack resistance. The glass is 0.6 mm thick, compared with 0.45 mm on the iPhone 17 Pro. The larger glass area may account for the added thickness.
- Fixation: The cover is held by adhesive around the edges and six metal clips. The two lower clips are locked in place by the bottom screws.
- Cold-carved Deco: Precise milling creates additional internal space within the Deco area. Semi-transparent injection molding on the edges improves drop resistance and secures the central metal plate.
- Rear camera protection: The single rear camera is protected by thick dustproof sealing foam. Conductive foam at the 5 o'clock position provides electrical shielding. Four rows of laser spot welding connect the outer steel ring to the inner reinforcement plate.
- Thermal management: Thermal film extends from the motherboard area to the bottom of the charging coil, covering approximately 4,500 mm². The motor area also receives thermal film. A MagSafe alignment magnet sits in the center.
Body Layout and Battery Space
The iPhone Air uses a three-section layout, similar to the Pro series. The motherboard is placed horizontally to reduce vertical use. This reduces stress on the board when the body bends. Foreign media bent an Air into a curved shape, and the device remained powered on.
- Upper section: main camera, Face ID, speaker, and motherboard.
- Battery: A steel-cased battery occupies about two-thirds of the internal space.
- Bottom section: A large motor is fitted in the limited space. As a result, there is no room for a second speaker. A future model that removes the USB-C port could potentially accommodate dual speakers.
The Deco bump remains visible even with the back cover removed. Apple trimmed the main camera module to fit the largest possible lens. As a result, the Deco shape does not match the rounded corners of the frame. The analysis suggests this change also serves a functional purpose.
The sound cavity follows the shape of the Deco. A recess in the center holds the flash and rear microphone. The T-shaped motherboard fits between the components. The A19 Pro sits at the center of the Deco bump.
A heat dissipation film on the motherboard carries an Apple logo. It is aligned with the phone's central axis.
Unlike pouch batteries in other iPhones, the battery has no buffer gaps or insulation partitions. Apple relies on the steel-cased battery's structural properties for safety. Even a space recessed by less than 1 mm is filled by the steel battery, which uses irregular polygonal shapes to maximize internal volume.
Display
- Supplier: The display is manufactured by LG.
- Panel: It uses the same Ceramic Shield 2 panel as the iPhone 17 series, with an anti-reflective coating.
- Thickness: The display is slightly thinner than the Pro's display.
- Dimming: The dimming behavior matches other models launched at the same time.
Brightness measurements
| Condition | Brightness |
|---|---|
| Manual, full screen | 782 nits |
| Strong ambient light | Close to 1,000 nits |
| 10% window | 2,770 nits |
The display is fixed by adhesive and six metal clips. The lower clips are locked by the bottom screws. Hidden metal brackets along the screen edges reinforce the Face ID module area. Positioning brackets prevent lens shift. Sealed foam protects the components from dust.
The front ambient light sensor is located beneath the display. Hidden metal brackets at the bottom protect the display driver IC (DDIC) and dissipate heat.
Bottom edge
- The bottom edge uses low-pressure injection molding, a process Apple has used on iPhones for several years.
- The injection area around the USB-C port is cut out to make room for the port, strengthen the connector, and center the port more precisely.
- The DDIC is moved upward compared with the Pro, to avoid the USB-C port. The injection area is wider and thicker to improve display reliability.
- The driver board IC is an Apple custom design. It has no identifiable markings on the silkscreen.
Camera button
- A 2 cm notch in the left injection area of the display aligns with the camera button on the frame.
- The frame opening for the button weakens this section. Apple added a reinforcement rib inside the button frame to maintain structural integrity.
Mid-frame on the display side
- The area for the display flex cables is thinned to reduce overall thickness.
- The display driver board area at the bottom is hollowed out to save space.
Front and Rear Camera Modules
The Face ID module integrates the front camera, dot projector, proximity sensor, and infrared camera. Its component arrangement differs from the Pro Max. The front camera modules of both models are identical, which indicates the iPhone Air uses the Sony IMX914 sensor from the iPhone 17 series.
The IMX914 is a square CMOS. The octagonal shape mentioned in an earlier video refers to the active sensing area, not the physical sensor shape.
The rear camera uses the Sony IMX904 sensor, the same as the 17 series. It has a 1/1.59-inch size, aperture, and sensor-shift optical image stabilization (OIS). None of these features are reduced. Machining marks on the metal roll cage indicate CNC processing.
Speaker
The iPhone Air has one speaker. A rubber ring at the sound outlet prevents sound leakage. The diaphragm measures 10.5 × 17 mm, which is among the largest diaphragms in top speakers the team has torn down. Speaker performance is lower than a dual-speaker configuration. The internal structure does not leave space for a second bottom speaker.
Motherboard
- Shape: The motherboard has a convex ("凸") shape. The raised top section fits into the extended Deco space.
- Layers: Only the top portion uses a stacked-board design. The rest is single-layer. The lower board is 0.54 mm thick.
- Connectors: The connectors lack foam rings for protection. Small components near the board are sealed with adhesive.
- Thermal management: Both sides of the motherboard are covered with thermal film. Screw holes are reinforced with metal plates.
Power management module
Beneath the front thermal film is a large integrated circuit. It is not one of the three core components. It is a SiP power management module that integrates power ICs and step-down circuits.
Modular power management simplifies post-repair service. In water-damage repairs, power-related faults often trace to nearby capacitors, resistors, or inductors. With a modular power module, technicians can replace the entire unit instead of testing each component. The approach also supports further motherboard miniaturization. For third-party repair shops, the impact is mixed. Modules like the power module are beneficial and add limited cost. Modular encrypted chips, however, make repairs considerably more difficult.
Thermal paste and SoC
Apple's dual-layer boards are filled with black thermal paste. Removing the paste exposes the SoC, which is covered by a black sticker. The sticker is a metal foil that also serves as a thermal material. Adhesive residue remains on the SoC.
Memory and processor
- RAM: Micron 12 GB LPDDR5X 8533, stacked with the A19 Pro using package-on-package (PoP) packaging.
- Processor: The A19 Pro in the Air is slightly downgraded. Details are available in Geekerwan's analysis.
- Storage: The ROM is Samsung TLC flash, placed back to back with the A19 Pro. The analysis notes that long-term high-load operation may affect thermal performance.
Wireless and RF components
- Wi-Fi and Bluetooth: Apple's N1 module supports Wi-Fi 7 and Bluetooth 6.0. It sits above the power management module.
- Baseband: Apple's C1X baseband is located above the board.
- RF transceiver: The RF transceiver below the board is also Apple's in-house design.
- Supplier mix: No RF-related chips at either end of the board come from Qualcomm. Some RF components still come from the three major U.S. RF suppliers.
- Signal performance: Signal quality requires evaluation through daily use.
The motherboard footprint is slightly larger than the Pro series, because the stacked region is limited.
Mid-frame motherboard area
The rear camera section has cushioning foam for lens protection. Conductive cloth provides electrical shielding. In the corresponding motherboard area, thermal film transfers heat to the frame. No thermal paste was found in this area.
Haptic Motor
- Type: An X-axis linear motor, located under a Taptic Engine sticker with graphite thermal film.
- Dimensions: 2.5 mm thick, with a volume of 528.7 mm³.
- Comparison: The motor is in the ultra-thin category within AAC's lineup. It is larger than Android counterparts CSA0916 and ESA1060.
- Performance: Apple's targeted tuning, precise control through the built-in Hall sensor, and the Air's slim body together produce haptic feedback that the analysis considers consistent with the iPhone standard.
Battery
- Removal: Small metal tabs on both sides indicate electro-induction battery adhesive. A DC adjustable power supply enables battery removal after power-on.
- Design: The battery uses a single-cell, single-connector design. Its shape indicates a stacked cell.
- Protection: The positive terminal on the protection board is wrapped in thick insulation. Under normal use, including extreme conditions, the design does not present a safety hazard.
- Thickness: 2.8 mm.
- Capacity: 3,149 mAh.
- Manufacturer: Huizhou Desay, using ATL cells.
Energy density
- The Air's energy density, calculated by package size, is about 783 Wh/L. This is similar to the two Pro models launched at the same time.
- The Galaxy S25 Edge, another slim flagship, has 758 Wh/L. The Air is slightly higher.
- Apple calculates battery density from rated (minimum) values. Direct paper comparisons therefore place Apple at a disadvantage. In practice, the Air's density is close to 800 Wh/L.
MagSafe battery pack
The MagSafe battery pack launched with the Air uses the same cells as the Air. Its capacity is also 3,149 mAh. Energy is lost during charging, so carrying the pack does not double the device's battery life.
USB-C Port
- Design: The port uses a single-tongue design. The injection-molded area matches the frame color, a long-standing iPhone design element.
- Speed: The port runs at USB 2.0 speeds of 480 Mbps.
- Corrosion protection: All pins are coated with an inert metal to improve oxidation and corrosion resistance.
- Pin configuration: The port is not a full-pin design. The Air is the second iPhone after the iPhone 16e with a Type-C port. It does not support DisplayPort video output.
Bottom Openings and Microphones
- Components: The bottom flex integrates the first bottom microphone and the barometric sensor. The bottom microphone module integrates a second bottom microphone and a pressure relief hole covered by a white waterproof breathable membrane.
- Openings: The four holes at the bottom serve three functions: two for the bottom microphones, one for balancing internal and external air pressure, and one vent for the barometric sensor.
- Water resistance: All openings passed the IP68 immersion test at six meters for 30 minutes.
- Material: The bottom area has seven openings in total and experiences frequent plugging and unplugging. Apple uses a titanium alloy part made with metal 3D printing for this area. Compared with traditional forging, metal 3D printing allows thinner parts with higher strength and less material waste.
USB-C alignment
The USB-C port is off-center in renders. On the physical device, the offset is less noticeable. The port is more centered than on the Galaxy S25 Edge. The bottom-right antenna module allows Apple to avoid coaxial cables, which would affect the device's appearance.
Top Components
- Microphones: The top flex integrates the top microphone. The device has four microphones in total, the standard iPhone configuration. The Air's microphones are smaller than the studio-grade microphones in the Pro models.
- Power button: A flex above the power button integrates a SiP module, likely for signal-related components.
- Antenna: A small antenna board above the volume keys has a protection level matching other components. All components on the board are sealed with glue.
Camera Button
- The camera button's backplate has a pressure sensor. The sensor design differs from the iPhone 16 series.
- A dome switch sits on the opposite side of the button.
- The button has a hard connection. Solder joints are hidden at the bottom of the button, and the button cannot be removed without damage.
Mid-Frame
- Anodization: The adhesive area for the battery has its anodized layer removed, so that a circuit forms when the device is powered.
- Battery bay: The battery bay thickness is less than 0.3 mm, which is close to the current CNC machining limit. Composite processes or new materials could reduce the thickness further.
- Construction: The mid-frame combines titanium and aluminum. The titanium alloy frame provides structural strength. The aluminum inner frame handles heat dissipation and load. Together with the Ceramic Shield panels on the front and back, the overall strength is considerably higher than expected.
- Finish: The polished titanium frame continues Apple's titanium finishes. The series moved from brushed finish on the 15 Pro, to matte finish on the 16 Pro, to polished finish on the Air. Fingerprints are the only visible drawback.
Assessment
The iPhone Air uses the most extensive internal stacking of any phone currently on the market. The teardown shows Apple testing miniaturization and further integration. The analysis suggests the Air previews design approaches for a future foldable iPhone. Leaks indicate that a foldable model would be similar in size to the OPPO Find N2.
Apple has prioritized repair-oriented materials and modular components. Extreme thinness involves trade-offs. The overall experience does not match traditional flagship designs in every respect. The Air's unboxing and physical design stand out in a market where few devices leave a strong impression.
Introduction and Back Cover
The host introduces the iPhone Air teardown and compares it with Android slim phones. The back cover is removed to reveal the Deco expansion platform and internal reinforcement.
- The video was filmed on Maui Island, Hawaii, after several flight connections.
- The iPhone Air is the focus among the iPhone 17 series; the host compares it with the Samsung S25 Edge.
- The Air uses a repair-friendly sandwich structure; screen and back cover can be removed separately.
- The back cover uses Ceramic Shield glass 0.6mm thick, versus 0.45mm on the Pro.
- Apple calls the raised area the "Expansion Platform" (officially "Plateau" in English).
- The back cover has six metal clips for reinforcement, with the two bottom clips locked by screws.
- A single rear camera is protected by dustproof foam; conductive foam provides shielding.
- The thermal film covers about 4500mm² from the motherboard to the charging coil.
Internal Layout and Battery Design
The battery occupies about two-thirds of the body. The motherboard is placed horizontally in a three-section layout, leaving no room for a bottom speaker.
- The steel-cased battery takes up about two-thirds of the space.
- The motherboard uses a three-section layout with horizontal placement to reduce stress from bending.
- The upper section holds the main camera, Face ID, speaker and motherboard; the bottom holds a large motor.
- A bottom speaker cannot fit, though dual speakers may be possible if the C port is removed in future.
- The Deco bump shape is trimmed so it does not match the frame's rounded corners.
- The A19 Pro sits at the center of the Deco bump; the heat dissipation film has an Apple logo along the central axis.
- The battery has no pouch buffer gaps or insulation partitions; steel-cased battery shapes are irregular polygons.
Screen Teardown
The screen is removed and examined. It uses an LG display with Ceramic Shield 2 and measured brightness values.
- The screen is slightly thinner than the Pro's.
- The display is from LG and uses the same Ceramic Shield 2 panel as the iPhone 17 series, with anti-reflective coating.
- Brightness: 782 nits manual full-screen, close to 1000 nits outdoors, and 2770 nits in a 10% window (HDR).
- The screen is fixed by adhesive and six metal clips; metal brackets reinforce the Face ID area.
- The DDIC was shifted upward to avoid the C port, and the bottom injection area was widened.
- A 2 cm notch on the display's left injection area aligns with the camera button; a reinforcement rib was added.
Cameras, Speaker and Motherboard
The Face ID module, front camera, rear camera and speaker are examined. The Air uses the Sony IMX914 front camera and the Sony IMX904 rear sensor.
- The front camera module is the same as the iPhone 17 series, using the Sony IMX914 square CMOS.
- The rear camera uses the Sony IMX904 sensor, 1/1.59-inch, with aperture and sensor-shift OIS.
- The single speaker has a 10.5x17mm diaphragm, among the largest in the host's teardowns.
- The motherboard is single-layer except for the top stacked section; the lower board is 0.54mm thick.
Motherboard Components
The motherboard contains a SiP power management module, Micron RAM stacked with the A19 Pro, Apple's N1 Wi-Fi/BT chip, C1X baseband and in-house RF parts. No Qualcomm RF chips are used.
- A SiP power management module is used, allowing easier replacement during repair.
- Micron 12GB LPDDR5X 8533 RAM is stacked with the A19 Pro using PoP packaging.
- The ROM is Samsung TLC flash, placed back-to-back with the A19 Pro.
- Apple's N1 chip supports Wi-Fi 7 and Bluetooth 6.0; the C1X baseband and in-house RF transceiver are used.
- RF chips are not from Qualcomm, but the device still depends on the U.S. RF big three.
Motor and Battery
The X-axis motor and battery are examined. The battery is 3149mAh, 2.8mm thick, from Huizhou Desay with ATL cells.
- The X-axis Taptic Engine is 2.5mm thick with a volume of 528.7mm³.
- The battery is 3149mAh and 2.8mm thick, made by Huizhou Desay using ATL cells.
- Battery energy density is about 783Wh/L, versus 758Wh/L for the Galaxy S25 Edge.
- The MagSafe battery pack uses the same cells (3149mAh) but energy loss during charging means it does not double battery life.
USB-C Port and Bottom Microphones
The USB-C port and bottom microphones are covered. The port is single-tongue, USB 2.0 speed, and the bottom has four holes: two microphones, one pressure vent and one barometer vent.
- The USB-C port is single-tongue and runs at USB 2.0 speeds of 480Mbps; it lacks DisplayPort video output.
- The Air is the second iPhone after the 16e with Type-C.
- The bottom has seven openings in total, passing IP68 at six meters for 30 minutes.
- The bottom section is made of titanium alloy using metal 3D printing, which is thinner and stronger.
Top Components, Camera Button and Mid-Frame
The top microphone, power-button flex, camera button and mid-frame are examined. The frame uses titanium-aluminum fusion, and the battery bay wall is less than 0.3mm thick.
- The device has four microphones, a standard iPhone configuration.
- The camera button has a pressure sensor and a dome switch, with solder joints hidden at the bottom.
- The mid-frame combines a titanium alloy outer frame and an aluminum inner frame.
- The battery bay wall is less than 0.3mm thick, near the current CNC machining limit.
Final Impressions
The host concludes the iPhone Air is the most extreme internal stacking in a phone today and a preview of Apple's next foldable. The practical trade-offs are noted.
- The Air is seen as paving the way for Apple's next-year foldable, possibly similar in size to the OPPO Find N2.
- The polished titanium finish is fingerprint-prone but has no other flaws.
- The Air's thinness brings trade-offs; the overall experience is not as complete as traditional flagships.
