~3m12:36
微机分WekiHome

ENG)iPhone 15 Pro 系列拆解:年复一年,还能看到未来么?【享拆】 - 微机分WekiHome

Sep 22, 2023

Read: ~3m · You save: 10 min

iPhone 15 Pro Series Teardown: Year After Year, Is There Still Anything New?

Tear down the iPhone 15 Pro piece by piece: titanium frame, A17 Pro chip, periscope camera, and cooling concerns revealed in this detailed teardown.

Source: WekiHome (微机分), published 2023-09-22

Overview

This teardown examines the iPhone 15 Pro and iPhone 15 Pro Max. The analysis covers the exterior design, the disassembly sequence, the internal components, and the thermal design. The author concludes that the most visible change is the thinner, lighter body, and that cooling performance and signal design remain open problems.

Exterior

  • Weight and feel: The 15 Pro measures 188 grams. The chamfered edges improve grip noticeably. The author states that the device feels markedly different from earlier Pro models.
  • Color: The author tested the blue and natural titanium finishes. The author states that the blue appears more subdued than in official images.
  • Fingerprints: Oil and fingerprints collect on the surface. Extended use darkens the color of the border area. The author does not consider this a significant problem.

Disassembly Procedure

Step 1: Card Tray Removal

  1. Power off the device.
  2. Remove the card tray, located on the left side of both models.

The tray holds two SIM cards, one above the other. The tray has a titanium alloy bracket and a dustproof and waterproof plastic ring on the inside.

Step 2: Screen Removal

The author notes that the iPhone 15 lineup uses sandwich construction for easier maintenance. Removal from the rear cover is theoretically possible. However, the battery connector and most interfaces sit on the front side, so the screen is removed first.

  1. Remove the two bottom screws. Apple has used this screw type since the iPhone 3G, and it remains in use.
  2. Heat the screen edge.
  3. Use an alcohol-dampened disassembly tool with tabs to cut the adhesive.
  4. Open the screen from right to left.
  5. Disconnect the battery connector.
  6. Disconnect the connector between the screen and the sensor unit.
  7. Remove the screen.

Screen findings:

ItemResult
Panel supplierSamsung, based on panel layout
SurfaceSuper Ceramic Crystal Glass
Dimming method480Hz low-frequency PWM
Manual full-screen brightness775 nits
Full-screen peak brightness1063 nits
Brightness versus predecessorEssentially unchanged

The rear of the screen is fully covered by a metal plate. A large thermal film covers the upper area. Compared with the previous generation, the film area is smaller. The telephoto module pushes the front sensor array further toward the edge.

Step 3: Motherboard Removal

  1. Remove all screws securing the motherboard cover.
  2. Remove the metal cover.
  3. Disconnect all ports on the motherboard.
  4. Remove the three screws securing the upper speaker, then remove the speaker.
  5. Remove all screws securing the motherboard.
  6. Flip up the motherboard. A wireless charging coil connector is fixed to its rear.
  7. Remove the cover plate.
  8. Disconnect the connector between the motherboard and the center frame.

Motherboard cover and layout:

  • The cover has nearly full-coverage thermal film on its front.
  • The main heat-generating area on the inside of the cover also has thermal film.
  • Cushioning foam sits at the corresponding interface positions.

The most visible layout change is the removal of the metal cover over the rear camera module. The previous generation, the iPhone 14 Pro Max, had a large empty space at that location. The telephoto module now occupies it. The author states that the layout proportions of major components are essentially unchanged from the previous generation.

The upper speaker's external dimensions show no significant change from the previous generation. The speaker's lead-in hole has a dustproof and waterproof plastic ring.

Step 4: Sub-Panel Removal

  1. Remove all screws in the sub-panel area.
  2. Disconnect the motor connector.
  3. Remove the bottom speaker and motor.

The motor is an X-axis linear motor. The author believes it uses Rasonic's second-generation SLA technology. The motor contains a Hall sensor that monitors oscillator position in real time. This allows precise regulation.

The author reports the following motor measurements:

  • iPhone 15 Pro Max: roughly 0921
  • iPhone 15 Pro: roughly 0919
  • Current Android maximum: 0916

The bottom speaker's external dimensions show no significant increase compared with the iPhone 14 Pro Max. The iPhone 15 Pro and iPhone 14 Pro are identical in this respect.

Step 5: Battery Removal

  1. Remove three adhesive strips.
  2. Remove the battery.

Both batteries use Apple's L-shaped design with a single cell and a single interface.

ModelCapacityChange from Previous GenerationManufacturer
iPhone 15 Pro Max4422 mAh+99 mAhHuizhou Desay
iPhone 15 Pro3274 mAh+74 mAhSynventive

Step 6: Tail Cable Removal

  1. Remove all screws in the tail connector area.
  2. Remove the two microphones.
  3. Remove the plastic holders for the microphone and barometer.
  4. Remove the two screws securing the USB-C connector.
  5. Remove the tail cable.

The tail cable integrates two bottom microphones, the barometric pressure sensor, and the USB-C interface. The interface supports the USB 3 specification at 10 Gbps. It also supports DisplayPort video output and 4.5 W reverse wired charging.

Step 7: Rear Cover Removal

  1. Heat the rear cover.
  2. Use an alcohol-dampened disassembly tool with tabs to cut the adhesive.
  3. Separate the rear cover.

Rear cover findings:

  • The back is glass. The design language has been used since the iPhone 11 series.
  • The glass is cold-carved. A single thick piece of glass is thinned to its final form.
  • The rear camera decoration is integrated into the rear cover. This removes a disruptive seam and one point of potential ingress for the waterproofing structure.
  • The inside of the cover appears to have a large thermal film. On closer inspection, the heat sink covers only the wireless charging coil and a small area in the upper left corner. The rest is black sticker material.
  • The wireless charging coil supports MagSafe and delivers 15 W.
  • The metal DECO trim in the upper right corner of the rear camera is metal.

Rear microphone and flash:

  1. Remove two screws.
  2. Remove the microphone cover. The rear microphone sits underneath. The device has four microphones in total.
  3. Remove the flash module. The flash is an adaptive, original-color flash unique to the Pro series. It adjusts intensity adaptively and offers improved brightness and uniformity. The flash has a dustproof and waterproof plastic ring on its inside.

Frame:

  • The outer frame is titanium alloy.
  • The inner frame is aluminum alloy.
  • The two metals are joined by solid-state diffusion. The author observed nanometer injection molding in the joint, which the presentation did not mention.
  • Titanium has a high strength-to-weight ratio. The author considers it a good balance of strength and weight, setting aside process cost.
  • The rear shell assembly of the 15 Pro is nearly 16 grams lighter than that of the 14 Pro.

Internal Components

Main Board and SoC

The main board uses Apple's sandwich design. The SoC sits between two board layers. The baseband chip is tightly packed. The ROM sits back to back with the SoC. Several major heat sources cluster together.

SoC: A17 Pro

  • Internal code: APL1V02
  • Process: the first commercial 3 nm SoC in volume production
  • Package: slightly smaller external size than the A16
  • Transistors: increased from 16 billion to 19 billion
  • GPU cores: increased from 5 to 6
  • The SoC silkscreen omits the model name, the first such case on an iPhone.

The author states that he is not satisfied with the performance of this SoC.

Other board components:

ComponentLocationNotes
U2 ultra-wideband chipLeft of SoC
Power management ICRight of SoCApple in-house, internal code APL109A
Baseband modemLower boardQualcomm X70
RF ICsUpper boardTwo SDR735 units
Wi-Fi/Bluetooth moduleBelow SoCUSI
RAMAbove SoCHynix LPDDR5, 8 GB
StorageSide of boardToshiba, labeled CAYAN; stated to start with K5A5; uses NVMe protocol; verified with third-party software

The Wi-Fi module's speed has increased.

Face ID Module

The Face ID layout matches the previous generation. From left to right, the components are the dot-matrix projector, the infrared camera, and the front camera.

Removing the module requires removing two screws.

Rear Camera Module

The three rear cameras sit inside a CNC-machined metal roll cage. The module is noticeably larger than the iPhone 14 Pro Max module.

  • Cushioning foam protects the area around the camera perimeter and the LiDAR scanner.
  • Thermal film covers the telephoto periscope position on the back of the module.
  • Cushioning foam covers the ultra-wide and main camera positions.

Camera findings:

  • The main camera's CMOS area is unchanged from the previous generation.
  • The 3x telephoto focal length of the 15 Pro is also unchanged.
  • The periscope telephoto lens is the new element. The author says it is the feature of greatest interest.

Periscope structure:

  • A three-axis anti-shake structure is used. Three balls are positioned at the vertical corners.
  • The prism is 2.77 mm thick.
  • The prism contains two light baffles to suppress stray light. A patent document describes this design.

The author compares the CMOS area with that of the Xiaomi Mi 13 Ultra.

LiDAR scanner:

  • The module was restructured.
  • Thickness decreased from 3.67 mm to 3.03 mm.
  • The new module projects a larger individual spot. The overall dot matrix is thinner than the previous version.

Antenna Module

Removing the center frame's top screws releases the top microphone bracket and the antenna module. The antenna module integrates the top microphone.

Thermal Design

The author identifies cooling as the main weakness.

  • Thermal grease: The heat sink is not filled with thermal grease. The motherboard touches the heat sink only at contact points, and a large heat pipe separates the components.
  • Heat dissipation: The author considers heat dissipation poor. He states that the 15 Pro's cooling design shares the same limitation.
  • Thermal conduction: The author considers the titanium frame's thermal conductivity questionable.
  • Structural design: The author states that the structural design compounds the problem. The source refers to it as "Kouzou 3A."

US and non-US versions:

  • The US version eliminates the physical SIM card slot.
  • The ROM moves into the position of the SIM card slot.
  • The author states that this layout places the ROM farther from the SoC in the US version.
  • Heat distributes more evenly across the US motherboard.
  • The author therefore expects the US version to cool slightly better than the GB version, based on theory.

The author states that a hard-to-replace component layout makes repairs more difficult.

Summary

The author's conclusions are as follows.

  • Core changes: The most noticeable improvement is the thin and light body. Structural optimization reduced thickness and weight.
  • Materials: The iPhone 15 Pro is the first phone to use a titanium alloy frame. The author expects domestic manufacturers to adopt similar materials and pursue cost reductions.
  • Periscope: The new periscope telephoto structure is the most significant internal addition.
  • USB-C: The switch to USB-C is a mandatory requirement.
  • Manufacturing: The author states that Apple's R&D and manufacturing reflect the standards of a top-tier manufacturer.
  • Open issues: The author identifies cooling performance and signal design as priorities. He states that the A17 Pro's performance gains from craftsmanship face a clear ceiling.
  • Outlook: The author considers the Vision Pro a product for a small group of users and does not expect it to affect the mainstream market in the near term.

Disassembly Scale

  • Total screws: 74
  • Screw types: 37
  • The author states that the device cannot be restored to its original state after disassembly.

Introduction and Exterior

The presenter introduces the teardown and highlights the 15 Pro's lighter, chamfered design, color options, and protective accessories.

  • Measured weight of the 15 Pro is 188 grams with chamfered edges, which improves grip
  • Blue color looks more subdued than in official pictures; the primary color is for recognition
  • Fingerprints and oil may darken the border area over time
  • Recommended accessories: Ultra-thin PP case plus ultra-thin tempered film, about 12 grams per set

Removing the Screen

Disassembly begins with removing the card tray and screen, which uses a sandwich construction and heat and adhesive-tab removal.

  • Card tray is on the left side; dual SIM placement is top and bottom with a titanium alloy bracket
  • Screen removal requires heating and using alcohol with dismantling tabs to cut the adhesive
  • Screen is Samsung, with Super Porcelain Crystal Glass, 480Hz low-frequency PWM dimming
  • Measured manual full-screen brightness up to 775 nits and full-screen excitation brightness 1063 nits
  • Rear of screen fully covered with a metal plate and thermal film; front sensor moved toward edge due to telephoto module

Removing the Motherboard and Components

The motherboard and rear camera module are removed, revealing a larger telephoto module, speaker changes, and a cooling design with no thermal grease.

  • Rear camera metal cover removed, leaving space now used by the telescope lens
  • Motherboard has no thermal grease filling, so heat dissipation is poor
  • US version eliminates the SIM card slot; ROM relocated, changing heat distribution slightly
  • Storage ROM is from Toshiba (CAYAN) with NVMe protocol; RAM is Hynix LPDDR5 8GB
  • A17 Pro is the first commercial 3nm SoC in large scale, with transistors increasing from 16billionto16 billion to 19 billion (as stated), and GPU cores upgraded from 5 to 6
  • Qualcomm X70 baseband, two SDR735 RF ICs, USI Wi-Fi/BT module, and Apple U2 ultra-wideband chip and PMIC
  • Camera module is CNC-machined metal roll cage; periscope telephoto has three-axis anti-shake and a 2.77mm prism
  • Laser radar module thickness reduced from 3.67mm to 3.03mm

Sub-panel, Motor, and Battery

The sub-panel section includes the bottom speaker and an X-axis linear motor with a built-in Hall sensor; batteries are L-shaped single-cell designs.

  • Motor has a built-in Hall sensor for real-time monitoring of oscillator position
  • Pro Max battery capacity is 4422mAh, up 99mAh from previous generation, made by Huizhou Desai
  • Pro battery capacity is 3274mAh, up 74mAh from previous generation, made by Synventive
  • Tail plug cable integrates two bottom microphones, barometer, and USB-C interface with 10Gbps USB 3 and DP video output, plus 4.5W reverse wired charging

Rear Cover and Frame

The back cover is glass with cold-carved thinning, integrated rear camera Deco, and a titanium outer frame with aluminum inner frame joined by solid-state diffusion.

  • Back cover is glass, a design language used since iPhone 11; cold carving thins the glass
  • Wireless charging coil supports 15W with MagSafe charger
  • Outer frame is titanium alloy and inner frame is aluminum alloy, joined by solid-state diffusion and nano injection molding
  • Back shell assembly is nearly 16 grams lighter than the 14 Pro
  • Titanium has questionable thermal conductivity, raising cooling concerns for the 15 Pro series
  • The device contains 74 screws of 37 types